Check Out Our FREE GUIDE: 25 MustHave Carpentry Tools...Under $25 Each!
https://www.thehonestcarpenter.com/
We consult with homeowners and property investors nationwide on a range of important homerelated issues, including:
Remodels and Renovations
Water Damage
Home Inspection Reports
Estimate and Proposal Analysis
Major Repairs
Contractor Issues
Just book a consultation on our home page!
FOLLOW US ON INSTAGRAM:
/ thehonestcarpenter
FOLLOW US ON LINKEDIN:
/ thehonestcarpenter
Check out our other houserelated videos, too!:
CAN FROST TILT A HOUSE?:
• CAN FROST TILT A HOUSE?! The Problem ...
WORST TERMITE DAMAGE I'VE SEEN:
• I Never Expected TERMITE DAMAGE THIS ...
11 WORST ROT AREAS ON YOUR HOME:
• 11 WORST ROT AREAS ON YOUR HOME!! (Yo...
All House Framing EXPLAINED...In Just 12 MINUTES! (House Construction/Framing Members)
Most people know that we call the assembled wooden structure of our houses "FRAMING." But, most people's knowledge of framing stops right there. This short video from The Honest Carpenter will explain what every major piece of framing in your house is called, how it works, and when it's installed!
Nearly every remodel, renovation and addition will involve new framing. And major repairs will also include a great deal of new framing. So it's very important to understand these terms so you'll know what your contractor is telling you!
FoundationThis is the bottom level of our houses, typically constructed by masons in the form of brick and block foundations, or poured concrete foundations.
Mud Sill / Sill / Sill PlateThis piece of framing sits directly on the masonry foundation. It is made of treated lumber, so it will resist rot while in contact with damp masonry. It runs the entire perimeter of the house.
JoistsThese are the framing members that create our floors and ceilings. They are made of dimensional lumber, like 2x10s, or possibly IJoists or Floor Trusses. The first level of joists sit directly on the mud sill.
Girders and BeamsThese are stronger horizontal structural members that carry the weight of several joists or trusses.
Columns and PostsThese are strong vertical framing members that bear the combined weight of girders and beams, as well as joists, and transfer it to a safe point down in the foundation, or a lower part of the structure. You also see them beneath decks, and porch roofs
SubFloorThis is a layer of tongueandgroove strand board or plywood that lays across the joists, creating a continuous surface to walk on and build more structure upon. It extends right out to the very edge of the structure.
StudsThis is a catchall term for framing members stood on end to create the vertical structure of our homes. Studs are typically in the 2x4 or 2x6 dimensions. They are staggered 16" or 24" center to center.
PlatesThese are the horizontal pieces of lumber that studs connect to at their ends. They turn the whole wall into a rigid structure that can be lifted into place. There is usually a single plate at the bottom of the wall, and a double top plate.
Doors and Windows receive special framing, because they create a hollow space in the wall for doors and windows to sit in.
HeadersThese are the pieces of wider framing, turned on end and facing outward, that carry the weight over doors and windws.
Jack Stud/Trimmer StudThese sit directly beneath the ends of the header, supporting it from below.
King StudThese sit just outside of the header and jack stud, and extend to the top plate.
Cripple StudsThese small framing members fill hollow spaces above door headers, or below windows. They create a continuous wall surface.
Rough Sill/Rough OpeningWhat we call the entire open space for a door or window to sit in.
Blocking/NoggingSmall horizontal pieces of framing between studs. They may prevent tall walls from bowing, provide a fireblock, or create support from fixtures.
StaircasesThese used to be made of notched stringers, but are now often ordered as preassembled units.
RaftersFraming that creates our roof; they act like diagonal joists.
Ridge Board/Ridge BeamThe tall board sandwiched between rafter peaks
Hip Rafter/Valley RafterThe rafters that create diagonal inside corners or outside corners of a roof.
Rafter TailsThe overhanging ends of the rafters (often tied together with a SubFascia)
Jack RaftersExtend from the ridge to a hip or valley rafter
Common RaftersExtend all the way to the Ridge Board.
TrussesPrefabricated units that create the structure and shape of a roof. They are made form shorter, skinner pieces, and pinned together with spiky metal plates.
SheathingThe plywood or strand board layer that wraps all the framing on the house exterior, creating a wall surface and providing stability.
Thanks for watching!