STL Files: https://www.planeprint.com/notos
Propeller Wall Art: https://cults3d.com/en/3dmodel/art/p...

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...


See what else I am working on:   / troymcmillan_rc  
  / troymcmillan_rc  

#3DPrinted,#RCAirplane, #ItFlies


3D Printers I use and recommend:
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
Ender3 V2: https://amzn.to/2SmLOGk
Twotrees SapphirePRO: https://amzn.to/3wtNOLz
Anycubic Mega X Printer: https://amzn.to/3f4oS89
Fokoos Odin5: https://amzn.to/3fAES06

3D Printing Filament:
ColorFabb LWPLA: https://colorfabb.com/lwplanatural
Esun ePLALW:
Overture White PLA: https://amzn.to/3facD9A
TPU: https://amzn.to/2Sw3Oe8

Supplies required for this Build:
Screw assortment: https://amzn.to/2SvMxSs
Carbon Rods: https://www.readymaderc.com
5x HS5055MG Servo: https://amzn.to/3fg4ctw
3542 1080KV Motor (Recommend 4S Battery 3050grams of thrust): https://www.altitudehobbies.com/produ...
13x4 Prop: https://www.apcprop.com/product/b13x4e/
60 amp ESC: https://amzn.to/3oK0jji
4s 2200mah Battery: https://amzn.to/3faeHOS

Tools and Supplies used:
Spektrum DX6 Controller: https://amzn.to/3l6NFsD
Receiver: https://amzn.to/3j4PbK4
Battery Charger: https://amzn.to/3vejwfL
Charge cable: https://amzn.to/34lOk3q
XT60 connector: https://amzn.to/3iyZWnf
Assortment of 3Pin Extension Cables: https://amzn.to/3l1xNYt
ZBend pliers: https://amzn.to/34mA0rt'>https://amzn.to/34mA0rt
2mm push rod ends: https://amzn.to/3nnjD4U
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
LowVoltage Tester: https://amzn.to/2Yk0A0w
Hot knife: https://amzn.to/3nrCwUH
Drill Bits: https://amzn.to/3nIJzrx
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
ZBend pliers: https://amzn.to/34mA0rt'>https://amzn.to/34mA0rt
Build Mat: https://amzn.to/3vJmauw
Onboard Camera: https://amzn.to/3rp2OrH
Lead weight: https://amzn.to/3cFnzeu


*These are the settings I used for my Artillery Sidewinder 3D Printer with White Overture PLA. These settings are not going to work with every printer, or every PLA. Printers have direct drive or different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!

I use my Direct Drive Artillery Sidewinder for PLA
PLA Settings
Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 100
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Enable Retraction – Checked
Retraction Distance – 1.3
Retraction Speed – 10
Retraction Extra Prime Amount – 0.3
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 20
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle

I used Twotrees Sapphire Pro for LWPLA
LW PLA Settings
Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 235
Build Plate Temperature – 60
Flow – 55%
Speed:
Print Speed – 100
Outer Wall Speed – 40
Inner Wall Speed – 40
Travel Speed – 80
Travel:
Enable Retraction – Checked
Retraction Distance – 3
Retraction Speed – 25
Retraction Extra Prime Amount – 0.8
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 20
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle






Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!