STL Files: https://3dprintz.at/produkt/longboar...
This is a full step by step build video of the Longboard 1000 from 3dprintz. This plane was fun to fly great first build project. This is a great plane to take out to the RC field with other planes or a great park flyer.
Thank you so much for watching!
Propeller Wall Art: https://cults3d.com/en/3dmodel/art/p...
If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...
See what else I am working on: / troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #ItFlies
More awesome Builds Here: https://3dprintz.at
Products Mentioned:
Artillery Sidewinder: https://amzn.to/396eqIp
Anycubic Mega X Printer: https://amzn.to/3f4oS89
Sapphire Pro Printer: https://amzn.to/2QudVSK
Fokoos Printer: https://amzn.to/2Q0uiqC
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
Folding Prop: https://amzn.to/32hZzHM
3S 450mah Battery: https://amzn.to/3nee5dv
2x 3.7g servo: https://amzn.to/3mR6kKg
2212 1400kv motor: https://amzn.to/3mP99vt
The Motor comes with a 30amp but use a 20 amp it is smaller and saves wight 30amp not required for this build.
20amp ESC: https://amzn.to/32kLUA0
4mm carbon fiber rod: https://amzn.to/3trYJEC
AR620 Receiver: https://amzn.to/3j4PbK4
DX6 Transmitter: https://amzn.to/3l6NFsD
ZBend pliers: https://amzn.to/34mA0rt
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
Drill Bits: https://amzn.to/3nIJzrx
Build Mat: https://amzn.to/3vJmauw
*These are the settings I used for my Twotrees Sapphire Pro 3D Printer with PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!
Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Material:
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 100
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Enable Retraction – Checked
Retract at Layer Change Checked
Retraction Distance – 5
Retraction Speed – 25
Retraction Extra Prime Amount – 0
Combing Mode – all
Cooling:
Enable Print Cooling – Checked
Fan Speed – 50
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!