Hey everyone! In this video, you get to build your own Arduinobased (up to 7CH) Hobbygrade Radio Transmitter and Receiver/Controller pair from scratch with NRF24L01 for any RC Models such as cars, boats, planes, and even drones. Closer to the end of the video, you see how a robot car is controlled with this homemade Radio control setup!

Code credits to Electronoobs for the TX and RX code Original Project Vdeo    • DIY Radio Controller  Arduino & NRF2...  

Visit my online Storefront: https://sites.google.com/view/maximag...

☕ Buy me a coffee: https://www.buymeacoffee.com/MaxImagi...

Instagram: @max.imagination https://www.instagram.com/max.imagina...
Instructables page: https://www.instructables.com/member/...

Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!


Link to a website with good info on the NRF24L01 Radio Transceiver module:
https://lastminuteengineers.com/nrf24...

Downloadable Circuit Diagrams for TX and RX:
https://drive.google.com/drive/folder...

Transmitter and receiver codes (CODE CREDITS: ‪@ELECTRONOOBS‬ ):
https://drive.google.com/drive/folder...

Transmitter's cardboard case sketches/blueprints:
https://drive.google.com/file/d/10CfK...

Transmitter and receiver codes for L298 Driven RC Arduino robot car:
https://drive.google.com/drive/folder...


Things needed for this project (with purchase links):
(x2) NRF24L01 + PA/LNA with antenna https://amzn.to/3EGRQYe
(x2) Arduino Nano https://amzn.to/3rXevrK
(x2) Joystick Module https://amzn.to/3EI9HOB
(x2) Large and small perforated prototyping PCB board for transmitter and receiver https://amzn.to/3Vryxs2
(x1) On/off switch https://amzn.to/3evOlcv
(x2) 25V 10mf capacitor https://amzn.to/3Tia32k
Female and male pin headers (for Arduino Nano) https://amzn.to/3EMol7s
(x1) Male and female JST connector pair https://amzn.to/3CCCp0v
(x2) 18650 LiIon 3.7V battery cell https://amzn.to/3zp86JQ
(x1) 3 pin 2 cell battery connector for charging and charger https://amzn.to/3CzrRPY, https://amzn.to/3ev5yD5
(x1) 22 Gauge 0.64mm roll of bare copper wire https://amzn.to/3Czs6KS
Thin connecting wires https://amzn.to/3TkqMCi
Cardboard sheet
Clear plastic container lid

Tools and extra supplies I use:
➡ Soldering Iron Kit https://amzn.to/3X6L5Wq
➡ Hot Glue Gun https://amzn.to/3E6trJG
➡ Drill Machine https://amzn.to/3EDe0u8
➡ Box cutter/Utility knife https://amzn.to/3hP9MGI
➡ XActo Hobby Knife https://amzn.to/3XbL7ML
➡ Cutting Matt (Green) https://amzn.to/3gil71A
➡ Needlenose Pliers https://amzn.to/3ECTKc3
➡ Wire Cutters for Electronics https://amzn.to/3ECut1B
➡ Wirestripping tool (Automatic) https://amzn.to/3hQsMVD
➡ Screwdriver kit https://amzn.to/3V6vgNX
➡ Heatshrink Tube Kit https://amzn.to/3AksTPE
➡ Jumper Wire Kit https://amzn.to/3UGhMZq
➡ Breadboard for Prototyping https://amzn.to/3GlF4ze
➡ Perf Boards, Pin headers, and Connectors Kit https://amzn.to/3AkySUw
➡ Superglue https://amzn.to/3EE6uis
➡ Duct Tape https://amzn.to/3g5mTU0
➡ Doublesided Tape https://amzn.to/3Edta82
➡ Kapton Tape (for battery leads) https://amzn.to/3X58bNl

tags:
max imagination, transmitter and receiver, arduino transmitter, arduino based transmitter, rc transmitter, nrf24l01, radio controller, DIY,NRF24L01, Remote Control, ArduinoBased, NRF24L01 Tutorial, Arduino RC Transmitter, Arduino RC Receiver, DIY Radio Controller, DIY Transmitter, DIY Receiver, NRF24L01 Transmitter, NRF24L01 Receiver, Arduino Radio Transmitter, Arduino Radio Receiver, Arduino Wireless Transmitter, Arduino Wireless Receiver, Arduino NRF24L01 Tutorial, NRF24L01 Wireless Control, Build Your Own RC Transmitter, NRF24L01 Radio Transmitter, RC Transmitter Receiver DIY, DIY Arduino RC Control, NRF24L01 Radio Receiver, NRF24L01 RC Transmitter, Arduino Wireless Transmitter Receiver, DIY RC Transmitter Receiver System

#arduinoproject #rctransmitter #remotecontrol