STL Files: https://www.eclipsonairplanes.com/pa...
Propeller Wall Art: https://cults3d.com/en/3dmodel/art/p...
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...
See what else I am working on: / troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #ItFlies
Panthera V2 Specifications:
RTF Weight LWPLA: 790 grams
Wing Span: 1350mm
Length: 990mm
Panthera Parts List:
221213 1400KV Motor: https://amzn.to/3zQDGhQ
30amp ESC: https://amzn.to/3zQ0gXO
8x6 Propeller: https://amzn.to/2VjUDBY
1000mAh Battery: https://amzn.to/353cLmf
4x 9g servos: https://amzn.to/31kj82B
2x8mm Screws: https://amzn.to/3p8gmqY
40mm Foam Wheels: https://amzn.to/2Ie853O
10x5x3 Magnets: https://amzn.to/3bzb4Pz
1/8” Wheel Collar: https://amzn.to/3p4tvl1
3pin wire assortment: https://amzn.to/3l1xNYt'>https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf'>https://amzn.to/3iyZWnf
2mm push rod ends: https://amzn.to/3nnjD4U'>https://amzn.to/3nnjD4U
Carbon Fiber Tubes/Rods: https://www.readymaderc.com
Fuselage: 4x 1.2mm x 1m
Elevator Hinge: 2mmx317mm
Flaperon Hinge: 2x 2mmx500mm
Wing Root: 6mm500mm
Wing Tip: 2x 4mm400mm
3D Printers I use and recommend:
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
Anycubic Vyper: https://amzn.to/3rPZ0RN
Anycubic Mega X Printer: https://amzn.to/3f4oS89
Ender3 V2: https://amzn.to/2SmLOGk
Twotrees SapphirePRO: https://amzn.to/3wtNOLz
Fokoos Odin5: https://amzn.to/3fAES06
3D Printing Filament:
ABS for motor mounts: https://amzn.to/3xgLI2c
ColorFabb LWPLA: https://colorfabb.com/lwplanatural
Overture White PLA: https://amzn.to/3facD9A
TPU: https://amzn.to/2Sw3Oe8
Tools and Supplies used:
Spektrum DX6 Controller: https://amzn.to/3l6NFsD
Receiver: https://amzn.to/3j4PbK4
Battery Charger: https://amzn.to/3vejwfL
Charge cable: https://amzn.to/34lOk3q
XT60 connector: https://amzn.to/3iyZWnf'>https://amzn.to/3iyZWnf
Assortment of 3Pin Extension Cables: https://amzn.to/3l1xNYt'>https://amzn.to/3l1xNYt
ZBend pliers: https://amzn.to/34mA0rt'>https://amzn.to/34mA0rt
2mm push rod ends: https://amzn.to/3nnjD4U'>https://amzn.to/3nnjD4U
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
LowVoltage Tester: https://amzn.to/2Yk0A0w
Hot knife: https://amzn.to/3nrCwUH
Drill Bits: https://amzn.to/3nIJzrx
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
ZBend pliers: https://amzn.to/34mA0rt'>https://amzn.to/34mA0rt
Build Mat: https://amzn.to/3vJmauw
Onboard Camera: https://amzn.to/3rp2OrH
Lead weight: https://amzn.to/3cFnzeu
LWPLA Print Settings:
Quality:
Layer Height – 0.25
Initial Layer Height 0.15
Line Width – 0.4
Walls:
Wall Line Count – 1
Z Seam Alignment User Specified
Z Seam Position Back (Position part to align Z seam)
Seam Corner Preference Expose Seam
Top/Bottom:
Top Layers 0
Bottom Layers 0
Infill:
Infill Density – 0
Material:
Printing Temperature – 235
Build Plate Temperature – 60
Flow – 55%
Speed:
Print Speed – 100
Outer Wall Speed – 55
Inner Wall Speed – 55
Travel Speed – 120
Travel:
Enable Retraction – Checked
Retraction Distance – 7.5mm (Bowden Tube Ender3)
Retraction Speed – 35mm/s
Retraction Extra Prime Amount – 0.2
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 80
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle
Music:
Joakim Karud:
YouTube: / joakimkarud
Soundcloud: / joakimkarud
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!