▶ Subscribe to my website (free): https://www.thehardwareguy.co.uk/subs...
▶ CNC Project Page: https://www.thehardwareguy.co.uk/diy...
As mentioned in my previous videos, one of my initial goals was to begin honing my skills in machining aluminum. Prior to handling any of the actual CNC frame components, I aimed to establish a high level of confidence in utilizing various tools and techniques, including hole drilling, counterboring, and thread tapping. To accomplish this, I intentionally acquired a piece of aluminum stock material to serve as a canvas for all my learning experiences and mistakes. Thus far, the process has been remarkably smooth. You can watch the YouTube video linked below, where I guide you through the tools and equipment I'll be using for machining the CNC frame. I was originally planning for this video to be singular, however, including the demonstrations the combined length would have been over 30 minutes. Therefore, it made sense to split this into two seperate videos for easier viewing. That means a double upload this week! Part 2 will be out this Wednesday at 6pm BST. See you there :)
▶Carveco: https://storeus.carveco.com/?ref=the...
▶DISCOUNT CODE: HWG5OFF
Tap Size Chart: http://www.custompartnet.com/tapsize...
▶ Draper Tap & Die Set
UK: https://amzn.to/3rIcTpg
US: https://amzn.to/3QbKsK1
▶ Metal Drill Bit Set
UK: https://amzn.to/3F7GQCr
US: https://amzn.to/48MIas4
▶ Counterbore Drill Bit Set
UK: https://amzn.to/3RR7183
US: https://amzn.to/3PP7yod
▶ Countersink Bit Set
UK: https://amzn.to/3QbIObj
US: https://amzn.to/3LPPiKc
▶ Step Drill Bit Set
UK: https://amzn.to/4700oVl
US: https://amzn.to/48MIpmY
▶ Metal Scriber
UK: https://amzn.to/3PQu9Rc
US: https://amzn.to/3ZKpmpb
▶ Molyslip
UK: https://amzn.to/3LSDzuh
US: https://amzn.to/3F5TguB
▶ Draper Center Punch
UK: https://amzn.to/46GyflN
US: https://amzn.to/3tpaeBv
▶ Deburring Tool
UK: https://amzn.to/3LUagYe
US: https://amzn.to/45pdM42
▶ Drill Press:
UK: https://amzn.to/3F0JuKc
US: https://amzn.to/3FgbZmZ
Engineering Square Set
UK: https://amzn.to/48HYxGf
US: https://amzn.to/3RR9jnF
▶▶ Watch the whole series of videos:
▶ Part 1: • DIY CNC 001 Introduction
▶ Part 2: • DIY CNC 002 Specification & Hardware
▶ Part 3: • DIY CNC 003 Tools for Machining Alu...
▶ Part 4: • DIY CNC 004 Drilling, Counterboring...
▶ Part 5: • DIY CNC 005 YAxis Frame Assembly
▶ Part 6: • DIY CNC 006 Gantry Assembly and Bra...
▶ Part 7: • DIY CNC 007 ZAxis Assembly
▶ Part 8: • DIY CNC 008 Linear Rail Installation
▶ Part 9: • DIY CNC 009 Surface Board, Spindle ...
▶ Part 10: • DIY CNC 010 Closed Loop NEMA Wiring...
▶ Part 11: • DIY CNC 011 VFD and Spindle Test
▶ Part 12: • DIY CNC 012 Electrical Control Box
▶ Part 13: • DIY CNC 013 Configuration & Basic T...
▶ Part 14: • DIY CNC 014 Motor Tuning, Squarenes...
As an Amazon Associate I earn from qualifying purchases.
If you purchase via my links, I receive a small commission, at no extra cost to you.