79in RC 3D Printed Eagle full step by step build guide. I will show how you can take a few roles of PLA and build this awesome flying RC Eagle from Planeprint.

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...

See what else I am working on:
  / troymcmillan_rc  
  / troymcmillan_rc  

#3DPrinted,#RCAirplane, #ItFlies

How to Print Thin Wall:    • How to Print Thin Wall  Planeprint |...  

STL Files: https://www.planeprint.com/eagle

Products Mentioned:
Anycubic Mega X Printer: https://www.anycubic.com/products/meg...
LWPLA: https://colorfabb.com/lwplanatural
White PLA: https://amzn.to/3ghcHl1
Black TPU: https://amzn.to/2Sw3Oe8
.030" clear Lexan sheet: https://amzn.to/3s4GSmv
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
2836 1120kv motor: https://amzn.to/30YhIKn
Folding Propeller: https://hobbyking.com/en_us/foldingp...
30amp ESC: https: https://amzn.to/2OJ94gk
3x HS55 Servos: https://amzn.to/3oRnDKV
1000mAh Battery: https://amzn.to/353cLmf
AR620 Receiver: https://amzn.to/3j4PbK4
DX6 Transmitter: https://amzn.to/3l6NFsD
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
YHarness: https://amzn.to/3jAFwvo
5mm magnet: https://amzn.to/35ZPLoN
Lead weight: https://amzn.to/3cFnzeu
Screw assortment: https://amzn.to/2SvMxSs
2mm push rod ends: https://amzn.to/3nnjD4U
ZBend pliers: https://amzn.to/34mA0rt
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
Hot knife: https://amzn.to/34AGOB1
Drill Bits: https://amzn.to/3nIJzrx
Build Mat: https://amzn.to/3vJmauw
Carbon Rods: https://www.readymaderc.com
Onboard Camera: https://amzn.to/3rp2OrH



*These are the settings I used for my Anycubic Mega X 3D Printer with White PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!

LWPLA
Temp 235c
Flow 55%
Retraction Distance – 2
Retraction Speed – 30
Retraction Extra Prime Amount – 0.3
All other settings the same as bellow:

Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 100
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Enable Retraction – Checked
Retraction Distance – 4
Retraction Speed – 30
Retraction Extra Prime Amount – 0.4
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 80
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle






Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!