STL Files: https://craycle.com/product/fpvorcastl/
STL Files coupon 10% OFF: troyorcav2stl
Printed Kits 5% OFF: troyorcav2printed
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...
See what else I am working on:
/ troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #ItFlies
Parts Required For this Build:
2207.5 2450 KV Brushless Motor: https://amzn.to/3GGi0te
30amp ESC: https://amzn.to/3xgNeRW
APC 6x4EP Prop: https://www.apcprop.com/product/6x4ep/
1000mAh Battery: https://amzn.to/3M8mGcC
Screw assortment: https://amzn.to/2SvMxSs
5mm Carbon Rod: https://amzn.to/3NcrL4G
4x ES08Mll Servos: https://amzn.to/3GDKxja
Or 4x Cheap servos: https://amzn.to/3ggbNsp
Supplies used:
FLSUN Super Racer: https://amzn.to/3t8H9Y2
AnyCubic Kobra: https://amzn.to/3wZHyx9
AnyCubic Vyper: https://amzn.to/3AJqwTM
ABS for motor mount: https://amzn.to/3xgLI2c
3DLabPrint PolyLight 1.0: https://3dlabprint.com/productcatego...
ColorFabb LWPLA: https://colorfabb.com/lwplanatural
eSun PLA+: https://amzn.to/3PSYspS
TPU: https://amzn.to/2Sw3Oe8
Spektrum DX6 Controller: https://amzn.to/3m21tGz
Spektrum NX10 Controller: https://amzn.to/3jnjvST
Receiver: https://amzn.to/3j4PbK4
Battery Charger: https://amzn.to/3M5EVzj
Charge cable: https://amzn.to/3M7CBHQ
Xt60 connector: https://amzn.to/3PWSowj
Assortment of 3Pin Extension Cables: https://amzn.to/3l1xNYt
ZBend pliers: https://amzn.to/34mA0rt
2mm push rod ends: https://amzn.to/3nnjD4U
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
LowVoltage Tester: https://amzn.to/2Yk0A0w
Hot knife: https://amzn.to/3nrCwUH
Drill Bits: https://amzn.to/3nIJzrx
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
Build Mat: https://amzn.to/3vJmauw
Onboard Camera: https://amzn.to/3rp2OrH
Lead weight: https://amzn.to/3cFnzeu
Soldering Iron: https://amzn.to/3NCsLiy
Printer Settings:
For printing the Orca V2 I used the FLSUN Super Racer that has a Bowden tube. These are the settings I used to slice my own STL files in Cura. The only settings you should need to adjust from these are individual printer settings like retraction and priming. There is also a slicing table at the bottom of the PDF, that outlines the few parts that need different top and bottom layers and infill settings. It also has the weights listed on the PDF to check your weights against.
Quality:
Layer Height – 0.2
Initial Layer Height 0.15
Line Width – 0.39
Walls:
Wall Line Count – 1
Z Seam Alignment User Specified
Z Seam Position Back (Position part to align Z seam)
Seam Corner Preference Hide Seam or Expose Seam
Top/Bottom:
Top Layers 0
Bottom Layers 2
Initial Bottom Layers 2
Infill:
Infill Density – 0%
Material: PLA
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 102%
Speed:
Print Speed – 100 mm/s
Outer Wall Speed – 50 mm/s
Inner Wall Speed – 50 mm/s
Travel Speed – 150 mm/s
Travel:
Enable Retraction – Checked
Retraction Distance – 6.5mm (Bowden Tube FLSUN Super Racer)
Retraction Speed – 40 mm/s
Retraction Extra Prime Amount – 0.2
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 80%
Support:
Generate Support NOT Checked
Build Plate Adhesion:
Build Plate Adhesion Type Skirt
Skirt Line Count 2
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!