Want to continue learning about engineering with videos like this one? Then visit:
https://courses.savree.com/'>https://courses.savree.com/
Want to teach/instruct with the 3D models shown in this video? Then visit:
https://savree.com/en'>https://savree.com/en
######################################################
Learn all of an internal combustion (IC) engine’s main parts and components, as well as the terminology and nomenclature associated with these engines (four and two stroke)!
Like this video? Then check out our other videos!
Marine Diesel Two Stroke Engine How it Works! • Marine Diesel Two Stroke Engine How...
Ship Parts and Terminology Explained! • Ship Parts and Terminology Explained!...
⚙How Deaerators Work! • How Deaerators Work (Engineering)
⚙How Shell and Tube Heat Exchangers Work! • How Shell and Tube Heat Exchangers Wo...
⚙How Power Grids Work! • The Electrical Grid and Electricity S...
⚙How Watertube Boilers Work! • The Electrical Grid and Electricity S...
⚙How Dams Work (Hydro Dams)! • How Dams Work (Hydro Dams)
Control Valve Types (Gate Valve, Globe Valve etc.)! • How Shell and Tube Heat Exchangers Wo...
Transformer Parts and Functions! • Transformer Parts and Functions
Plate Heat Exchangers Explained! • Video
Want to learn more about engineering?
Then join saVRee to access over 45 hours of engineering video courses! New courses every month!
https://courses.savree.com/'>https://courses.savree.com/
Hope to see you on a course soon!
Want to use the 3D model in this video to present, instruct, or teach? Simply join saVRee! We have over 400 engineering models that will make your life a lot easier!
https://savree.com/
You can learn more about engineering in our technical encyclopedia: https://savree.com/en'>https://savree.com/en/encyclopedia
▶Introduction
Piston internal combustion engines are also known as IC engines. IC engines are usually petrol/gasoline fired or diesel fired, but it is possible to use other fuels as well e.g. methane gas.
All of an engine's main parts are discussed in detail during the video. The engine shown in the video is a fourstroke diesel engine although it has similarities to a fourstroke petrol engine. Two stroke engines have a much simpler design, less parts, and thus they weigh less (with a correspondingly high power to weight ratio).
A fourstroke combustion engine consists of the following main parts:
Rocker Arm – presses down upon the valve bridge or valve stem.
Tappet Clearance – space between valve tip and rocker arm.
Valve Spring – returns valves to closed position when rocker arm not applying force.
Fuel Injector injects fuel.
Fuel Inlet Pipe – transfers fuel to the fuel injector.
Suction Valve – allows air into the combustion space.
Exhaust Valve – allows exhaust gas to exit the combustion space.
Fuel Injector Nozzle – sprays atomised fuel into the combustion space.
Clearance Volume – the volume calculated between top dead centre and the top of the cylinder.
Swept Volume – the volume based upon the stroke of the piston and area of the cylinder bore.
Cylinder Volume – the total volume within the cylinder.
Cylinder Bore – the internal diameter of the cylinder.
Compression Ratio – a calculation based upon the volume ratios within the cylinder. Petrol/gasoline engines have a low compression ratio (69:1) whilst diesel engines have higher compression ratios (1420:1).
Top Dead Centre (TDC) – a piston’s furthest point of transit towards the inlet and exhaust valves.
Pushrod (push rod) – transfers force from the cam lobe to the rocker arm.
Piston Crown – the top of the piston.
Piston Ring Grooves – where the piston rings locate within the piston.
Piston Rings used to seal the space between the piston and cylinder liner.
Stroke – the distance the piston travels from bottom dead centre (BDC) to top dead centre (TDC).
Piston – the piston.
Piston Skirt – the piston skirt (may be short or long).
Piston Pin / Gudgeon Pin / Wrist Pin – the connection between the piston and connecting rod.
Cylinder Wall – the boundary of the combustion space (also sometimes called the cylinder liner).
Cylinder Liner – the internal surface of the cylinder.
Camshaft – used for controlling engine timing such as fuel injection and valve timing; driven by the crankshaft.
Cam / Cam Lobe – presses against the tappets to actuate the rocker arm(s).
Cam Follower – is pushed by the cam and transfers the movement to the push rod.
Bottom Dead Centre (BDC) – the closest point a piston reaches to the crankshaft.
Connecting Rod (Con Rod) – connects the piston to the crankshaft.
Crank Web – used to reduce vibration and balance the engine; part of the crankshaft.
Crankpin Bearing Journal – crankpin bearings are installed between the connecting rod and crankpin.
#saVRee_Nuggets, #saVRee